|
Quantity
|
Total
|
||
|
|
|||
|
|
|||
Ready-to-install single-phase backup power kit
Ready-to-install single-phase backup power kit based on the Victron Energy Quattro 48/8000/110-100/100 230 V 8 kVA / 6.5 kW and a LiFePO₄ Sunlight Power ESS 51.2 V 100 Ah battery provides an energy reserve of 15.36 kWh, automatic switching between the grid and the battery (≤20 ms), and a high charging rate — up to 2.4 hours.
The runtime is listed in the technical specifications depending on the load power.
Unlike budget alternatives, this kit offers unique technological capabilities that ensure comfort, stability, and complete control over the power supply for your home or business.
Unique Features of the Victron Quattro Inverter
⚡ Two independent AC IN inputs — complete flexibility
The Victron Quattro inverter has two full-featured mains inputs (AC IN 1 and AC IN 2), opening up a wide range of application options:
- Connecting two independent inputs from different substations or power sources — the system can automatically switch between them based on priorities. For example, if power is lost on the main input, the Quattro instantly switches to the backup. A combination of grid and generator.
- Grid + generator combination — a classic scenario where AC IN 1 is connected to the utility grid, and AC IN 2 is connected to a diesel or gasoline generator.
🔄 Intelligent generator control algorithm
- Automatic start: when the battery charge level (SoC) drops to a set threshold—for example, 25%—Quattro sends a command via Cerbo GX Mk2 to automatically start the generator with mandatory preheating.
- Parallel operation: while running, the generator not only powers the load but also charges the battery via a powerful built-in charger
- Automatic shutdown: once the set charge level is reached (for example, 90%), the system switches the generator to cooling mode, lets it run for a few minutes at idle speed, and then automatically shuts it down.
- Flexible schedule: Using Cerbo GX, you can set a schedule specifying the hours when the generator is allowed to run (for example, from 8:00 AM to 10:00 PM), and at night—disable auto-start to avoid noise
- Remote control: the owner can disable automatic startup and start or stop the generator manually from a smartphone or computer. At the same time, you can immediately set the maximum runtime (for example, 60 minutes).
⚙️ Working with weak generators
The PowerControl and PowerAssist features allow the Quattro to operate even with low-power generators.
When the load exceeds the generator’s capacity, the inverter draws power from the battery, and when the load decreases, recharges the batteries.
This ensures stable operation without the risk of overloading the generator and without power outages, even during peak times.
⛽ Fuel Monitoring and Maintenance
We offer installation of a fuel level sensor , the data from which is displayed in the Cerbo GX / VRM system.
The owner can view the current fuel level, and the system can send a notification if the tank is running low (this feature is supported by Cerbo GX via an analog input).
The system also keeps track of the generator's operating time and reminds you of maintenance tasks—oil changes, filter replacements, or spark plug inspections.
Total-Energo LLC provides a full range of services for generator maintenance and repair, including sensor calibration, starting system checks, and integration with VRM.
Advantages of the TQS 230V Kit
⚡ High power handling from the mains
When connected to the grid, the system can pass up to 22 kW, allowing you to run several high-power devices simultaneously. The limitation to the inverter’s rated power of 6.4 kW applies only when operating on batteries.
🚀 Peak power 16 kW
Thanks to its high overload capacity, the system easily starts powerful pumps, refrigeration compressors, HVAC equipment, and electric motors even when running on battery power.
🔋 Fast battery charging
The built-in powerful charger allows you to fully charge the battery in just 2.4 hours, so the system is always ready for new outages.
The battery charging process is controlled by the built-in BMS (Battery Management System), which continuously exchanges information with the charger during the charging process. Voltage and current are adjusted according to the battery’s requirements.
This functionality makes the backup power system completely safe to use.
📱 Full control from your smartphone
Thanks to the apps VictronConnect and VRM Portal, you gain full control over the system in real time. On the screen, you can see:
- presence or absence of the grid;
- current load;
- battery charge level (%);
- charger status.
We will help you set up notifications for all key events:
-
switch to battery power;
-
power restoration;
-
critical battery discharge or overheating;
-
starting or stopping the generator (if connected);
-
any errors or overloads.
Use convenient Victron widgets to quickly monitor the system status right on your phone’s home screen.
⚙️ PowerControl and PowerAssist
If your grid is weak and the circuit breaker trips frequently, the Victron system can help. Thanks to the PowerControl and PowerAssist features, the inverter supplements grid power with battery power, allowing you to safely use high-power appliances.
📞 Call our managers to find out how this feature can help you specifically.
☀️ Solar Ready — ready for solar energy
All system components are fully ready for operation as part of a solar power plant. Quattro inverters are compatible with grid-tied inverters from Fronius, SMA, and ABB, and SolarEdge grid-tied inverters, making it easy to convert an existing system into a hybrid setup—with the ability to store energy in a battery and operate even without grid connection!
🔄 Scalability
Inverters Quattro can be connected in parallel or in a three-phase configuration. You can start with a single-phase solution and then expand the power or switch to a three-phase system.
Sunlight batteries support operation of up to 32 modules in parallel, thanks to special firmware developed for Victron Energy inverters.
🛡️ 100% safe to use
The kit is installed in accordance with all manufacturer requirements and the actual conditions at the customer's site. The system continuously monitors hundreds of parameters—from load and voltage to temperature and battery status.
In case of a deviation from the norm , a service notification is sent to the service center of Total-Energo LLC and to the user.
🧾 Warranty and Certification
Installation is performed in accordance with the manufacturers' instructions, which guarantees free replacement of components under warranty (5 years).
For private, commercial, and government clients, an annual service contract is available, which includes:
- software updates to the latest version
- analysis and monitoring of parameters
- checking connections and nodes
All major system components have international and Ukrainian certifications, which is important for participation in “green tariff” or “net-billing” programs.
The kit includes
1 × Cerbo GX MK2 Victron Energy Communication Center
1 × Victron Energy Quattro 48/8000/110-100/100 48/230V 8kVA/6.5kW hybrid
1 × Victron Lynx Power In 1000 (M10) Modular Distribution Busbar
1 × Battery Switch ON/OFF 275A
3 × Victron MEGA-fuse 100A/80V
1 × Victron MEGA-fuse 300A/80V
3 × Sunlight Power ESS LiFePO₄ Battery 51.2V 100Ah with built-in BMS
1 × Quattro Inverter Setup with LiFePO₄ Batteries
1 × Installation Kit for Consumables 230V 10-15kW
1 × 19" 16U Battery Rack (400 mm depth)
3 × 400 mm 1U 19" battery shelf
⚙️ Installation Algorithm
Needs Assessment
The first stage, during which the manager identifies the tasks that the UPS system must address. This provides us with a preliminary technical specification.
Preliminary Calculation
To agree on the cost of the system and select the optimal configuration.
Reservation and payment
Reserving the necessary parts in stock, generating an invoice, and, if necessary, preparing a supply contract.
Engineer visit to assess the site
An on-site inspection is sometimes required, for example, when installing high-power systems, or for additional work, such as when an uninterruptible power supply (UPS) system needs to be integrated with an existing generator.
Preparation of consumables
Fastening materials, AC and DC cables, protective and insulating materials, etc.
Electrical installation work
Delivery and electrical installation work usually take place on the same day. Installation time ranges from a few hours to several days for high-power systems. The cost of delivery and electrical installation services is calculated separately for each case.
Commissioning and Testing
Configuration and verification of the uninterruptible power supply unit’s operation in all modes: charging, discharging, simulation of power outage and restoration, etc.
Handover of documentation and management rights
Warranty card and, if necessary, additional documents (certificates, delivery notes, etc.), as well as user training. User registration for the VRM cloud service and transfer of rights for monitoring and operating the system. If necessary – assistance with installing apps on the phone for control and configuring push notifications.
Online support via VRM
The UPS will be under constant monitoring to ensure there is no indication of any potential mismatch in power or battery capacity. The service center monitors all technical parameters of each component to ensure they remain within normal ranges.
Consulting
Throughout the entire service life, we provide remote support and answer your questions. If necessary, engineers will visit the site.
Annual Maintenance
We strongly recommend performing annual maintenance on your systems to ensure 100% compliance with manufacturers' requirements.
💬 Get professional advice right now!
We support our clients at every stage—from equipment selection to post-warranty service.
Call us or submit a request on the website — engineers from Total-Energo LLC will select the optimal system configuration tailored to your specific needs.