|
Quantity
|
Total
|
||
|
|
|||
|
|
|||
Inverter RS 48/6000 230V Smart – a state-of-the-art inverter with a battery charging function from grid-tied inverters, which allows you to build powerful off-grid solar power plants up to 72 kVA in single-phase mode and 216 kVA in three-phase mode. It supports connections to VE.Direct, VE.Can, and Bluetooth, allowing you to connect external MPPT trackers, modern battery monitors, establish communication with LiFePO4 battery BMS, and remotely monitor, control, and configure settings via the VictronConnect App, including full control via the internet and the official VRM cloud service.
Key advantages of the Victron Energy RS 48/6000 230V Smart inverter
- Synchronization with grid-connected PV inverters – when external grid-connected PV inverters are connected to the output of the Inverter RS 48/6000 230V Smart, excess solar energy is used to charge the batteries. With the Inverter RS 48/6000 230V Smart, a grid-connected solar power plant is upgraded to a hybrid system.
- 230 V pure sine wave (or 400 V for three-phase systems) – stable voltage for sensitive devices.
- 6000 VA (4500 W) power – high performance for off-grid systems.
- Peak power of 9000 W for 3 seconds – supports loads with high inrush currents or 7000 W for 4 minutes!
- Supports parallel operation of up to 12 units – 6 x 12 = 72 kVA / 54 kW.
- Supports three-phase operation – generation of true three-phase 400V 50Hz voltage with a 120° phase shift ensures reliable operation of all motors, compressors, and any other three-phase loads.
- Built-in Bluetooth – parameter monitoring and configuration via VictronConnect.
- Two VE.Can & VE.Direct ports – monitoring via GX devices and the VRM platform. Full remote system control.
- Efficiency up to 96.5% – minimal energy loss.
- Programmable relay – for automation (generator, alarm system, etc.).
- Low standby power consumption (20 W) – minimal impact on batteries.
- Lightweight – only 11 kg – easy to install in various power systems.
Technical Features
- Battery charging current 85A – get a powerful charger and fast charging for a large battery to store a large amount of energy.
- Support for high-power grid inverters – a 5000W grid inverter can be connected to a single Inverter RS 48/6000 230V Smart. Accordingly, for a three-phase configuration with three Inverter RS 48/6000 230V Smart units – 15 kW.
- Battery temperature sensor included!
- Frequency shift function – intelligent control of any grid-connected inverter thanks to the frequency shift function. A single data communication protocol with Fronius inverters.
- Intelligent overheating protection – if the ambient temperature rises and the inverter’s power section begins to overheat under heavy load, the inverter does not shut down immediately, unlike budget alternatives; it will continue to operate in limited power mode.
- Wide battery input voltage range – from 36 to 60V, allowing you to connect almost any type of battery that can be used for operation.
Use Cases
- Off-grid solar stations – ensuring stable power supply in systems with high-capacity batteries and solar inverters.
- Commercial facilities – backup power source for small and medium-sized businesses.
- Industrial power systems – supporting the operation of sensitive equipment in industrial environments.
- Off-grid power for homes – automatic power supply to critical devices during power outages.
- Three-phase systems – support for complex three-phase power grids with the ability to connect in parallel.
Communication interfaces
- VE.Bus – the ability to integrate Victron Energy products and configure data exchange with batteries from Pylontech, Sacred Sun, Sunlight, and dozens of other manufacturers.
- Programmable relay – any automation is also possible, such as controlling a generator based on the battery charge status.
- Optional VE.Bus Smart dongle – adds Bluetooth communication with the ability to perform fine-tuning of the device.
- Optional VE.Bus to USB cable – for programming from a computer.